null

Tycon Systems TPDIN-SC48-20 V2+ 48V 20A MPPT Smart Temp Comp Solar Charge Controller

SKU:
TPDIN-SC48-20 V2+
$569.95
UPC:
810017121694
Width:
5.90 (in)
Height:
5.40 (in)
Depth:
4.40 (in)
Shipping:
Calculated at Checkout

Description

MPPT Solar Controller w/ Remote Monitor and 7 Port Gigabit Passive PoE Switch

V2+ 48V 20A MPPT Smart Temp Comp Solar Charge Controller w/ 7 Port GigE Passive PoE Switch/Remote Monitor

The newest in our TPDIN series of products is the TPDIN-SC48-20 v2+. It is a web manageable MPPT Solar Controller with built-in 7 Port Gigabit Passive PoE switch. The controller uses temperature compensated smart battery charging to properly charge GEL or AGM or Lithium batteries and extend their life. It has a balance charge mode for periodic battery bank maintenance and can charge batteries that are dead. There are 4 Gigabit 802.3at or 24/48V Passive PoE and 3 Gigabit 24/48V Passive PoE ports. Each port is capable of 0.645A Max. There is a wire terminal auxiliary output capable of 2.25A maximum. Total from all outputs is set at 150W at 48VDC and 72W at 24VDC for a max total of 222W. Outputs can be switched by user between 802.3at (port 1-4 only), 48VDC, 24VDC or OFF through the web interface. 

The web interface has full capabilities to measure and log battery voltage, battery current, input voltage/current, load current and battery temperature. Ports can be controlled by a settable ping watchdog to power cycle the port if communications to the unit are interrupted. Auxiliary port can be controlled by voltage or temperature or time so it can be programmed to control lights, pumps, generators, heaters, fans, etc. The unit supports automated Email alerts if user programmed limits are exceeded so that the user can be alerted in case of developing problems at the site.
The controller can also be powered through an external AC to DC power supply connected to the PV+/PV- input in order to charge the batteries from an AC source like grid power or generator. All inputs and outputs are surge and overload protected. Connectors and battery fuse are removable for easy maintenance. The controller can be mounted using the integral DIN rail mount bracket or using 2 mounting tabs.

Features 

  • TPDIN® MPPT 48V 20A Solar Controller
  • Temperature Compensated Smart Battery Charging
  • 7 Port Gigabit PoE Switch • Remote Monitor and Control
  • 48V or 24V User Selectable Output Voltage
  • 2.25A Auxiliary Wire Terminal Output
  • Total 200W Power Output
  • Automatic Low Voltage Battery Disconnect
  • DIN Rail or Screw Tab Mounting

Specifications

Solar Input Voltage

56VDC Min to 100VDC Max

Max Solar Panel Open Circuit Voltage (Voc)

100VDC (Maximum worst case over full temperature range)

Max Solar Panel Power Point Voltage (Vmp)

90VDC

Solar Input Current

20A Maximum

Typical Controller Efficiency

96% (68VDC Input, 10A Load, 25C)

MPPT Tracking Frequency

19 times/sec or 19 Hz

Battery Voltage

48VDC (Controller will function down to 20VDC)

Battery Current

20A Maximum

Battery Type

GEL or AGM or WET or Lithium

Charging Volts at 25C

AGM= Float:55.2, Bulk:57.6V, Balance:58.4V (60 Min)

GEL= Float:55.2, Bulk:56.8V, Balance:Disabled

WET= Float:55.2, Bulk:58.4V, Balance:59.2V (60 Min)

Lithium= Float:Disabled, Bulk:57.6V, Balance:Disabled

Temperature Compensation

-3mV/°C/2V

Fuse Type

58V 20A Automotive Mini Blade Type (Littlefuse0997020.WXN)

Low Voltage Disconnect

42V to 48V – settable in web interface

Low Voltage Disconnect Recovery

44V to 54V – settable in web interface

Auxiliary DC Output Voltage

24VDC or 48VDC – settable in web interface

Auxiliary DC Output Current

2.25A Maximum Continuous, 3A Max peak

Auxiliary DC Output Controls

Temperature, Voltage, Time – settable in web interface

PoE Switch

Qty 7 RJ45, 10/100/1000MB Gigabit Ethernet, Layer 2, Auto Crossover

PoE Output Voltage

802.3at (port 1-4 only), 48VDC or 24VDC or OFF – settable in web interface

PoE Output Power

0.645A per PoE Port Max

PoE Power supplied on pins 4,5 (V+) and 7,8 (V-) (Mode B)

Port Surge Protection

IEC 61000-4-2 (ESD) 15kV (air), 15kV (contact)

IEC 61000-4-4 (EFT) 40A (5/50ns)

IEC 61000-4-5 (Lightning) 25A (8/20µs)

Maximum Power Output

222W Total (150W @ 48VDC and 72W @ 24VDC) from all output ports (including Aux Output), Auto Shutdown and Autorecovery from Fail

Indicator LED’s

Charge (Green), 24VDC (Green) or 48VDC (Yellow) Port Voltage, Overload (Red)

Measurement Accuracy (V / I / T)

+/- 0.1V , +/- 0.1A , +/- 1 Deg C

Power Consumption

3.5W Typ

Accessibility

Via Web Browser and SNMP

Data-Logger

FIFO, 15,000 data sets, Programmable log interval

Wire Size

Solar and Battery – 8AWG, Aux DC Output -12AWG

Mounting

DIN Rail or 4mm Screw Tab

Operating Temperature

-40C to +65C (-40F to 149F)

Humidity (RH)

0% - 90%

Dimensions (LxWxDepth)

151mm x 111mm x 138mm (5.9 x 4.4 x 5.4”)

Weight

1.5kg (3.3lbs)

MTBF

>100,000 Hrs

Certifications

FCC/CE EN55022 (EMC) ; CE EN55024 (EMC); CE/UL EN60950-1 (LVD)

Warranty

3 Years

Extra Information

Brand:
Tycon Systems
Width:
5.90 (in)
Height:
5.40 (in)
Depth:
4.40 (in)
Weight:
3.30 LBS