The EZ-Bridge® LT+ HD is a high power 25dBm (316mW) outdoor wireless bridge system operating in the 5GHz unlicensed frequency spectrum providing real world throughput up to 100 Mb/sec. It complies with the 802.11g/n or 802.11a/n standards to insure interoperability. The EZBridge® LT+ HD creates a transparent wireless bridge between two networks up to 3 miles apart with good line of sight. It supports VOIP, VPN, multiple MAC addresses and DHCP across the wireless link. It is the perfect plug and play solution for connecting the networks in two or more buildings, internet access sharing, remote video surveillance or remote network access. Multiple EZ-Bridge® LT+ HD units can be connected in a mesh configuration to allow interconnecting more than two sites.
With its password verification, MAC address authentication, SSID suppression and advanced WPA encryption, the system provides the best available wireless data security.
Installation is a snap because of the plug and play features which have been built into the system. Just install the antennas and plug in the power inserters. The units will automatically find their peer and create a secure wireless network link. If changes to the pre-configured settings are desired, they can be easily done thru the built-in web interface from any point on either side of the network. There are no drivers or software that needs to be loaded to the computer.
The EZ-Bridge® LT+ HD comes complete with all the electronics that are needed for a point to point wireless network bridge installation; including 2 powerful 14dBi 802.11g/n or 16dBi 802.11a/n MIMO antennas with built-in high power electronics, Bracket Kits which accommodate pole or wall mounting, Surge Protected Cat5e rated 24V PoE (Power Over Ethernet) power inserters and 75’ shielded outdoor rated CAT5 cable assemblies.
The EZBR-0516+ management interface is IPv6 enabled, https enabled. Logon username is fixed. The password can be changed, and there are no rules for password length or content.
- EZ-Bridge LT5+ HD Industrial Strength 100MB 5GHz Wireless Point to Point Secure Bridge Pair, Includes outdoor Shielded CAT5 Cables and Surge Protected PoE Inserters
- Plug and Play Simplicity, Just Point and Power Up via 12-24V Passive PoE (PoE Injectors incl)
- Layer 2 Transparency, Supports VOIP, VPN, Multiple MAC Addresses and DHCP Across the Wireless Link
- Only 4W Average Power Consumption, Great for Solar Powered Systems
- Conforms to Wireless Standards 802.11an, Wall or Pole(1-2") Mounting Brackets Included
5GHz 802.11n: up to 300Mbps
5GHz 802.11a: up to 54Mbps
IEEE802.11g/n, 802.11a/n, 802.3, 802.3u
Power Supply: 100-240VAC 50/60Hz
EZ-Bridge®: 12VDC to 24VDC Passive PoE
Average Power Consumption: 4W
FCC Part 15 / UL
RF Frequency Band
5100 ~ 5850 MHz
Receive Sensitivity (Typical)
802.11n: -90 dBm
802.11g: -75 dBm
802.11a: -75 dBm
DC Connector Power Out
Input Voltage @ Max 10W
5GHz 16dBi MIMO Panel Antenna, 27deg Beamwidth, >22dB front to back
Operation Mode – Bridge or Router
Point to Point Bridge, Access Point, Access Point WDS, Client, Client WDS
10/100Mbps RJ-45 LAN Port x 2
Static or Auto configuration using DHCP Client
MAC Address Filtering, WEP/WPA encryption, Hide SSID in beacons, Layer 2 isolation
Web-based configuration (HTTP)
Console configuration (SSH)
Upgrade firmware via web browser
Antenna Physical Dimensions (L x W x D)
314mm x 187mm x 65mm
12.4” x 7.3” x 2.5”
Complete System Weight
3 kg (7 lbs )
-30°C to +70°C (-22°F to 158°F)