Description
The EZ-Bridge® LT+ HD is a high power 25dBm (316mW) outdoor wireless bridge system operating in the 5GHz unlicensed frequency spectrum providing real world throughput up to 100 Mb/sec. It complies with the 802.11g/n or 802.11a/n standards to insure interoperability. The EZBridge® LT+ HD creates a transparent wireless bridge between two networks up to 3 miles apart with good line of sight. It supports VOIP, VPN, multiple MAC addresses and DHCP across the wireless link. It is the perfect plug and play solution for connecting the networks in two or more buildings, internet access sharing, remote video surveillance or remote network access. Multiple EZ-Bridge® LT+ HD units can be connected in a mesh configuration to allow interconnecting more than two sites.
With its password verification, MAC address authentication, SSID suppression and advanced WPA encryption, the system provides the best available wireless data security.
Installation is a snap because of the plug and play features which have been built into the system. Just install the antennas and plug in the power inserters. The units will automatically find their peer and create a secure wireless network link. If changes to the pre-configured settings are desired, they can be easily done thru the built-in web interface from any point on either side of the network. There are no drivers or software that needs to be loaded to the computer.
The EZ-Bridge® LT+ HD comes complete with all the electronics that are needed for a point to point wireless network bridge installation; including 2 powerful 14dBi 802.11g/n or 16dBi 802.11a/n MIMO antennas with built-in high power electronics, Bracket Kits which accommodate pole or wall mounting, Surge Protected Cat5e rated 24V PoE (Power Over Ethernet) power inserters and 75’ shielded outdoor rated CAT5 cable assemblies.
The EZBR-0214+ management interface is IPv6 enabled, https enabled. Logon username is fixed. The password can be changed, and there are no rules for password length or content.
Features
- High Power Electronics and powerful antenna - Operation up to 3 miles with good line of sight and up to 15 Mbps; 20Mbps for 5GHz Version
- True Plug and Play- No driver needed. Pre-configured at the factory for automatic peer to peer communications
- 64 and 128bit WEP, WPA and WPA2 Encryption- Most powerful data security available
- Web-based configuration - Remotely change device configuration or update firmware from anywhere on the network
- Power over Ethernet - Antennas can be mounted up to 100meter (300ft) from the power source
- Transparent Bridge - Appears to network devices as if an Ethernet cable has been installed between the 2 network nodes. Passes DHCP and supports multiple MAC addresses
EZBR-0214HD+ Specifications
|
Data Rates 2.4Ghz 802.11n: up to 300Mbps 2.4 GHz 802.11g: up to 54Mbps
Standards IEEE802.11g/n, 802.11a/n, 802.3, 802.3u
Power Requirements Power Supply: 100-240VAC 50/60Hz EZ-Bridge®: 12VDC to 24VDC Passive PoE Average Power Consumption: 4W
Regulatory Certifications FCC Part 15 / UL
RF Frequency Band 2400 ~ 2497 MHz 5100 ~ 5850 MHz
Modulation Technology 802.11n: TDMA 802.11g: OFDM 802.11a: OFDM
Receive Sensitivity (Typical) 802.11n: -90 dBm 802.11g: -75 dBm 802.11a: -75 dBm
Transmit Power 25dBm 316mW
DC Connector Power Out Input Voltage @ Max 10W |
Antenna 2.4GHz 14dBi MIMO Panel Antenna, 35deg Beamwidth, >20dB front to back
Operation Mode – Bridge or Router Point to Point Bridge, Access Point, Access Point WDS, Client, Client WDS
Interface 10/100Mbps RJ-45 LAN Port x 2
IP Configuration Static or Auto configuration using DHCP Client
Security MAC Address Filtering, WEP/WPA encryption, Hide SSID in beacons, Layer 2 isolation
Management Configuration Web-based configuration (HTTP) Console configuration (SSH) SNMP Protocol
Firmware Upgrade Upgrade firmware via web browser
Antenna Physical Dimensions (L x W x D) 314mm x 187mm x 65mm 12.4” x 7.3” x 2.5”
Complete System Weight 3 kg (7 lbs )
Operating Temperature -30°C to +70°C (-22°F to 158°F)
Warranty: 2 Years |